Rockbox General > Rockbox General Discussion
Data abort at 30801294 . . . Sandisk Sansa e260v2
CurlySue:
So far so good, Bilgus! ;D
As I did with RB 3.14, I am going to shutdown the e200v2 and let it sit for an hour or so - then power on and see what happens. 8)
That said, thus far, other than preferring EQ setting increments of 0.1 versus 0.5 (as is with this initial release of RB 3.13), all systems are a GO!! ;D
At this point, how would you like to proceed with further analysis and testing? I'm happy to play guinea pig - and I am equally interested in UPDATING the DEV BUILDS with RB 3.13 particularly if/when the BUILD improves FIDELITY. Let me know. ;)
Thanks again! :)
CurlySue
Bilgus:
ok here is the latest dev build compiled let me know what the data abort window has just like you did with the previous ones
http://www.mediafire.com/file/vprh3gin02lwz8j/SansaE_200v2_9-10-17_rockbox-full.zip
there isn't any need to shut it off for 60 minutes in between just a simple reboot will suffice
CurlySue:
Understood.
To ensure I am on the same page - it seems odd to me that I have 3.13 installed
and I am updating with a DEV BUILD for 3.14 without ever installing RB 3.14 . . .
While I am clearly showing my ignorance, had this been (oh say) January 2017
where, hypothetically, I may have been running the RB 3.13 with the latest DEV
BUILD. And after a few months of installing the latest DEV BUILDS, along comes
RB 3.14 . . . and like everyone else, I would have followed the instructions to
install 3.14 over 3.13 - instead of installing the next DEV BUILD (which would
have been a 3.14 DEV BUILD) over the existing/previous 3.13 DEV BUILD. Not
sure my point is 100% clear, but I'm gonna run with it and see if you understand
my concern/point here.
BACK TO THE ANALYSIS
I did install SansaE_200v2_9-10-17 and, thus far, no problem with thumb-wheel
volume control.
GOOD WORK, Bilgus!! BRAVO!!
What next?
CurlySue
Bilgus:
Ok so same error# same address, pc, sp.
Again the latest dev build of 3.13 is 3.14 there is NO clear delineation besides doing a bisect to find what commit caused the error but first I need to figure out what is causing it.
http://www.mediafire.com/file/6wt5uo861i4u8q6/SansaE200v2_NO-lcd_bitmap_transparent_part_rockbox-full.zip
Try this build and see if the error goes away or is different.
Do note your screen may not update properly/look weird
if you still have the last build I sent installed you only need to copy rockbox.sansa to the .rockbox directory on your device
AFTER you try the above build try this one and see if the error is back and/or if it changes
http://www.mediafire.com/file/mhgdh0gpkeccgqd/SansaE200v2_-R_d787191_g1499_rockbox-full.zip
CurlySue:
> Ok so same error# same address, pc, sp.
Data abort at 30801294
FSR 0x8
(domain 0, fault 8)
address 0x691789F4
pc:30901294 sp:300A9CF0
bt end
> Again the latest dev build of 3.13 is 3.14 there is NO clear delineation besides doing a bisect to find what commit caused the error but first I need to figure out what is causing it.
Please note that I am not asking for the "latest dev build" but I am asking for a dev build prior to RB 3.14 (since the build associated with its' release appears to be the problem here) . . . where I can obtain one of the last dev builds for 3.13 and the Sansa e200v2 Series player - before RB 3.14 was released (let's say 2 months before)?
> http://www.mediafire.com/file/6wt5uo861i4u8q6/SansaE200v2_NO-lcd_bitmap_transparent_part_rockbox-full.zip
> Try this build and see if the error goes away or is different.
Will do . . . and, as noted above, please let me know where I can obtain one of the last dev builds for 3.13 and the Sansa e200v2 Series player - before RB 3.14 was released (let's say 2 months before)?
> Do note your screen may not update properly/look weird
Prior to installing the above BUILD, note that my LCD already FLICKERS BRIGHTLY and DOUBLE CLUTCHES upon startup of RB.
> if you still have the last build I sent installed you only need to copy rockbox.sansa to the .rockbox directory on your device.
I have already scrubbed that BUILD and re-installed RB 3.13 (which works). Therefore I will install the full BUILD (noted above).
> you try the above build try this one and see if the error is back and/or if it changes
Will do. Thanks again, Bilgus!!
CurlySue
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version