Support and General Use > Audio Playback, Database and Playlists

My Computer does not Recognise my Sansdisc e200 01.01.07p,

<< < (4/7) > >>

Dasha:

Hi chronon me again ::) I have just  performed the following:
Turn on Player showed RB 5 then went Back to SDK Splash, Drives Recognized,>Download 1.2.2 >Run Boot utility > open>Etc >Unzipped all files>Settings\Temporary Internet Files\Content.IE5\DT58QUQ0\rbutilqt-v1.2.2[1] > Next >In RB Utility> Min Install/ Download 3.3 successful

It still goes Black screen, unless I hold down the Forward Button then it Goes SD Splash/Rockbox5/ RB Firmware/ Then back to SD Slash/Refresh Data/SD Music,Settings Etc/
In Sandisk settings still Say's Version010107P” should I get a Gun and Shoot It ;D Dasha

BruceHP:
It is very hard to follow your posts.

Did you Start RockBox Utility on your computer?  Did RockBox Utility recognize your Sansa player.

Try this without the SD card inserted.

Also, Check the Root Directory of your player for the .Rockbox Folder.  I don't believe you have installed RockBox as of yet.

Dasha:
Sorry bruceHP I will try and make this more detailed: :)
If I  Turn on my SansDisk normally And Or by Connecting Via the USB Cable to my Computer:
It show’s /the Yellow Rockbox (5) Logo / Then the Rockbox Firmware (black writing)/
Then it will go back to SansDisc Splash and the Computer Brings up a Page for SansDisc Drive E and Removable drive F (Both Drives are Recognized)/ At the same time it does :
/ Refresh Data /  Then  Music or Settings Etc Mode / Then back to the: / SansDisc Connected Splash /

As you Guy's advised I Downloaded Rockbox 1.2.2 Install / Run “Boot utility” / open / Etc / Unzipped all files to Settings\Temporary Internet Files\Content.IE5\DT58QUQ0\rbutilqt-v1.2.2[1]/
Then In the Rockbox Utility I clicked / Minimum Install / and then it came up / Download 3.3 successful /
If I start without using the USB cable and not connected to the Computer It still goes / Black screen/ unless I hold down the “Forward Button” then it goes to / Yellow Rockbox (5) Logo / Then the Rockbox Firmware/ SansDisc Splash / Then back to SD Slash/Refresh Data/SD Music or Settings Etc Mode/
However in in USB or Normal Start if I go to /SanDisk menu / SansDisk Settings / It still Say's  “Version010107P” Etc
I hope this is more legible thanks Dasha ;D

BruceHP:
As of yet I don't think you have installed RockBox on your player.  You might have the Bootloader.

Remove the SD card.
Start the player in the MSC mode.
Plug it into your computer.
Start Rockbox Utility.
Does it recognize your player in the Device line at the top .
If not click on Browse and Autodect.
If that doesn't work, hand select your device from Brouse.
Go to Installation tab.
Click Install Rockbox.
Click Current build.
Unclick the Dackup and Cache Boxes.
Click  Install.
Once this completes, close RButility and disconnect your player.
Shutdown the player and then Start it.

Hope this works.

Dasha:
Hi bruceHP :) Well I did as you said to the letter,R/box utility recognised the [drive (E)  Sansdisc e200] All went well however there is no change except the SD card has been removed as you required.
I have to hold down both the 'Reverse Button' and start button when I "start" it or if goes to "black screen"?? ??? ::)

I managed to get some more info from the R/box Firmware on start:
[Calculated CrC32 -- 6842]
[binary type rp05]

If I  Turn on my SansDisk normally And Or by Connecting Via the USB Cable to my Computer:
It shoe's /the Yellow Rockbox (5) Logo / Then the Rockbox Firmware
[Calculated CrC32 -- 6842]
[binary type rp05(black writing] 
Then it will go back to SansDisc Splash and the Computer Brings up a Page for SansDisc Drive E and Removable drive F (Both Drives are Recognized)/ At the same time it does :
/  Refresh Data /  Then  Music or Settings Etc Mode / Then back to the: / SansDisc Connected Splash / thanks you have the patience of a saint bruceHP, Dasha

Navigation

[0] Message Index

[#] Next page

[*] Previous page