Ukraine online ....still need help with sansa e280r

[tmt]

OK in this time I'll tried  my best with my english so I hope some body will understand me and HELP me!!!
So....I tried to install rockbox   everything was looking good but after installing nothing happened/ it was just screen which was showing just sandisk screen saver & that was it.when I backup the old version of firmware. & then I tried to install rockbox again but when I tried to patch it, it did not detect sansa in right way so I read how to make it back  & I tried to instal i2c-e280.bin and everything was going good but somewhere after 5 minutes of waiting it was looking like it's stuck on one point so I just remove battery and after that it does want to work in any way not in recovery mode not in any other ... just blue button & that is it.... I realy need help    
 Thanx for you time hopу somebody will understand Ukrainian english  

[AlexP]

I have removed your other thread as you have just started this one that is identical.  Please have some patience.  If someone reads it who knows the answer I am sure they will try to help.

[zajacattack]

Since you interrupted it writing the i2c rom, it is probably in pre-boot mode.

Follow the instructions at http://www.rockbox.org/twiki/bin/view/Main/SansaE200Unbrick#Pre_boot_Mode

[tmt]

Since you interrupted it writing the i2c rom, it is probably in pre-boot mode.

Follow the instructions at http://www.rockbox.org/twiki/bin/view/Main/SansaE200Unbrick#Pre_boot_Mode

I would like to but I can NOT get to the recovery mode!!!!
non of the buttons want еще work not "middle" one not "rec"

[zajacattack]

You have to fix the i2c rom, then use e200tool to boot into recovery mode. I said you were in PRE-BOOT mode, which is different than RECOVERY mode (see "Sansa USB Modes" at http://daniel.haxx.se/sansa/e200.html)

[tmt]

You have to fix the i2c rom, then use e200tool to boot into recovery mode. I said you were in PRE-BOOT mode, which is different than RECOVERY mode (see "Sansa USB Modes" at http://daniel.haxx.se/sansa/e200.html)

maybe I can't understand U... can you explain to me little bit )))
And I'm telling you one more time  I can't get
NOT to recovery mode
NOT to manufacture mode

[tmt]

SO... I don't have Linux & I tried windows way...
http://www.rockbox.org/twiki/bin/view/Main/SansaE200RBootloaderPatching#Bootloader_Patching_in_Windows
but when I'm connecting sansa to computer it detecting it like flash drive with out any drivers & the way that is on the page is also don't want work it can't driver in e200tool folder
what to do

[tmt]

ok!there is the thing....
I have the same problem that most of the people here black screen & blue light around middle button .. non of modes dont want to work I get Knopix but what ever....I don't know what to do
Also I have a problem with understanding English because I'm from the Ukraine!

so I'm asking  
IS ANY ONE WHO CAN GIVE INSTRUCTION STEP BY STEP HOW I CAN MAKE MY SANSA GET LIVE AGAINE!!!

P.S. I already spend like 3 days non sleeping trying to find out what I can do. Please I really need help!Hope for yours understanding .....

[zajacattack]

That page is for installing rockbox, not for recovering. The Windows version (and driver) of e200tool is at http://www.rockbox.org/twiki/bin/view/Main/WebHome?topic=UsefulSansae200Tools

[zajacattack]

1. Get the Linux copy of e200tool at http://daniel.haxx.se/sansa/e200tool.html
    Also, from that site, download an i2c rom file, a firmware file, and a bootloader file and put them in the same folder as e200tool
2. Connect your Sansa
3. Using the terminal, navigate to the folder you saved e200tool to (i.e. "cd /whatever/whatever/where_e200tool_is", without the quotes)
4. Type "e200tool init" (without the quotes) and hit enter in the terminal
5. Then, run "e200tool i2c program i2c.bin" (without the quotes)
6. Then, ONLY WHEN IT FINISHES, disconnect and then re-connect your Sansa
7. Run "e200tool recover BL_SD_BoardSupportSD.rom" (without the quotes) while holding record until you get into recovery mode
8. Copy the firmware and bootloader to the recovery disk
9. Disconnect and it should be fixed

Also, note, any of the file names above should be replaced with whatever you named the files when you downloaded them.

[tmt]

yahoo  
now my player is absolutely dead!!!!!
i used e200tool in Linux  everything was great except now I dont have even blue light ....
any Ideas...

[Febs]

tmt, I have split out your posts from the "Bricked e200" thread and well as zajacattack's reply and merged them into this thread.

BigBambi has already asked you this once, and I am going to reiterate it:  please DO NOT post the same question in multiple places.  It makes the discussion disjointed.  Please keep all discussion of this problem in this thread.

With respect to your comment, "now my player is absolutely dead," please describe in detail what you have done so far.

[tmt]

I did almost all things that ajacattack wrote to me but now i don't have even blue ring of death on my sansa but now its detecting in windows as usb driver part number vid_6666&pid_e200...
so I think it's ok but what I have no idea what to do now!!!!  
thank you for  you understanding!!!!
waiting for new answers!!!!

p.s. hope I didn't make it worse.....

[tmt]

1. Get the Linux copy of e200tool at http://daniel.haxx.se/sansa/e200tool.html
    Also, from that site, download an i2c rom file, a firmware file, and a bootloader file and put them in the same folder as e200tool
2. Connect your Sansa
3. Using the terminal, navigate to the folder you saved e200tool to (i.e. "cd /whatever/whatever/where_e200tool_is", without the quotes)
4. Type "e200tool init" (without the quotes) and hit enter in the terminal
5. Then, run "e200tool i2c program i2c.bin" (without the quotes)
6. Then, ONLY WHEN IT FINISHES, disconnect and then re-connect your Sansa
7. Run "e200tool recover BL_SD_BoardSupportSD.rom" (without the quotes) while holding record until you get into recovery mode
8. Copy the firmware and bootloader to the recovery disk
9. Disconnect and it should be fixed

Also, note, any of the file names above should be replaced with whatever you named the files when you downloaded them.

when I'm doing part number 5 it's writing to me
"Failed to claim the interface (-1, Operation not permitted)"
What should I do???

[zajacattack]

Try a different USB port or a different computer (are you on Windows or Linux?).