Installation / Removal > Sandisk - Installation/Removal

E250R "Load main image failed" after running install steps

<< < (2/4) > >>

John Brown:
I think you skipped the linux part like me  ;D
like they said if you don't have linux you don't have rockbox.
so you have to wait.

scorche:
No...we said a liveCD will work just fine.

Febs:

--- Quote from: Shane on September 05, 2007, 07:23:56 PM ---I think you skipped the linus part like me  ;D
like they said if you don't have linus you don't have rockbox.
so you have to wait.

--- End quote ---

Repeat after me:

L-I-N-U-X

clutch:

--- Quote from: chrisjs169 on September 05, 2007, 04:07:38 PM ---From what it looks like, you didn't patch the bootloader (properly).  Either follow the steps exactly or follow the steps to recover your Sansa.

--- End quote ---

This is what I saw when I first tried to patch bootloader:

root@localhost sansa]# ./e200tool recover BL_SD_boardSupportSD.rom
e200tool v0.2.3-alpha (c) by MrH 2006, 2007
Searching for device 0781:0720 ... found!
Initializing USB stub (4780 bytes) ... done!
Writing 'BL_SD_boardSupportSD.rom' to address 0x10600000
Searching for device 6666:e200 ... 9 found!
Write at 0x1065fc38
Write done!
Running from address 0x10600000
Searching for device 6666:e200 ... found!
Execution started!
[root@localhost sansa]#    

The screen on my sansa alternated between
LUN0 locked
LUN0 unlocked
LUN0 locked
LUN0 unlocked
LUN0 locked
LUN0 unlocked
LUN0 locked
LUN0 unlocked

for a number of minutes.  Eventually I pulled the plug and battery on it and it booted normally on power up.  Was the above message normal?

I decided to do the boot loader install proceedure again from the start.  I have the same message rolling on screen now.  I have to go to work, I'll leave it looping until morning in this part of the world.

Thanks
Clutch

chrisjs169:

--- Quote from: clutch on September 05, 2007, 10:00:17 PM ---
--- Quote from: chrisjs169 on September 05, 2007, 04:07:38 PM ---From what it looks like, you didn't patch the bootloader (properly).  Either follow the steps exactly or follow the steps to recover your Sansa.

--- End quote ---

This is what I saw when I first tried to patch bootloader:

root@localhost sansa]# ./e200tool recover BL_SD_boardSupportSD.rom
e200tool v0.2.3-alpha (c) by MrH 2006, 2007
Searching for device 0781:0720 ... found!
Initializing USB stub (4780 bytes) ... done!
Writing 'BL_SD_boardSupportSD.rom' to address 0x10600000
Searching for device 6666:e200 ... 9 found!
Write at 0x1065fc38
Write done!
Running from address 0x10600000
Searching for device 6666:e200 ... found!
Execution started!
[root@localhost sansa]#    

--- End quote ---
Make sure you hold REC when booting.

--- Quote ---The screen on my sansa alternated between
LUN0 locked
LUN0 unlocked
LUN0 locked
LUN0 unlocked
LUN0 locked
LUN0 unlocked
LUN0 locked
LUN0 unlocked

for a number of minutes.

--- End quote ---
This is considered normal.  Simply unmount the Sansa, and you can disconnect it.


--- Quote ---Eventually I pulled the plug and battery on it and it booted normally on power up.

--- End quote ---
So you didn't give it time to write the bootloader...


--- Quote ---I decided to do the boot loader install proceedure again from the start.  I have the same message rolling on screen now.  I have to go to work, I'll leave it looping until morning in this part of the world.

Thanks
Clutch

--- End quote ---
(cut and paste) This is considered normal.  Simply unmount the Sansa, and you can disconnect it.  It will keep 'looping' forever until you disconnect the Sansa.

Navigation

[0] Message Index

[#] Next page

[*] Previous page