Rockbox Technical Forums

Support and General Use => Hardware => Topic started by: mrsubway on March 16, 2011, 10:26:19 PM

Title: Sansa Clip Plus Refreshing your media
Post by: mrsubway on March 16, 2011, 10:26:19 PM
I know that as of right now, the USB mode in the Sansa Clip+ is disabled in Rockbox.  That's okay, but everytime I connect to USB, I get the refreshing your media prompts, which lasts for about 5 minutes.  Then when I add or change files and disconnect, I have to wait for it to go through this again.  Is there a way to disable this, or is it simply something the original firmware has to do.  Not a high priority question, but I'm curious.
Title: Re: Sansa Clip Plus Refreshing your media
Post by: gutaperek on March 20, 2011, 04:13:00 AM
1
Title: Re: Sansa Clip Plus Refreshing your media
Post by: TheAlmightyGuru on April 12, 2011, 02:46:12 PM
Same here. I've got a 32 GB SDHC card, and every time I do so much as rename a song, I have to wait ten minutes before I can listen to music again.

I saw on anythingbuipod.com someone posted this:

If you're using Rockbox, you can use the file browser to delete the ## folders, then if you fill the internal memory to within 90mb of the max, it won't refresh the DB when you unplug it. It will prevent you from using the OF though, so this only applies if you have Rockbox.

Is this correct? What are those ## folders for? I don't want to delete them if they're important.
Title: Re: Sansa Clip Plus Refreshing your media
Post by: LivArt on April 16, 2011, 04:39:27 AM
It runs! I've deleted every folder with ## and when I disconnect player, it shows original menu instead of "refreshing database". I have 200MB free in player.  But must'nt change anything on the player (add/delete songs etc.).
Title: Re: Sansa Clip Plus Refreshing your media
Post by: keyb_gr on April 18, 2011, 12:10:46 PM
How do you even access these ## folders? They don't show up in the file browser for me at all, even though database creation does index them. ???

Anyway, in my experience the OF skips database refresh when connecting to a computer. Then, after modifying whatever it was, "safely remove" the device and forcibly shut it down while it's still connected by holding the power button long enough. Unplug the cable, and you're good to go.
Title: Re: Sansa Clip Plus Refreshing your media
Post by: Roseweave on April 21, 2011, 07:18:51 AM
Having the same problem. There must be a more convenient solution?
Title: Re: Sansa Clip Plus Refreshing your media
Post by: Carson Dyle on April 22, 2011, 09:02:20 PM
There must be a more convenient solution?

Turn the player off while it's still connected to USB, disconnect the USB, then power up and it will boot directly into Rockbox without the Sansa firmware doing its refresh of media. If you've just finished a file operation, make sure you wait a few (10-20) seconds before powering down, just to be safe.
Title: Re: Sansa Clip Plus Refreshing your media
Post by: TheAlmightyGuru on April 27, 2011, 03:50:01 PM
The Clip+ doesn't seem to want to turn off while it's connected to USB. How do you do it?
Title: Re: Sansa Clip Plus Refreshing your media
Post by: Carson Dyle on April 27, 2011, 05:51:11 PM
The switch. It takes a while - maybe 20 seconds or so.
Title: Re: Sansa Clip Plus Refreshing your media
Post by: TheAlmightyGuru on April 29, 2011, 02:23:43 PM
Ah, cool! Thank you sir!
Title: Re: Sansa Clip Plus Refreshing your media
Post by: gyboth on October 04, 2011, 06:21:19 AM
Turn the player off while it's still connected to USB, disconnect the USB, then power up and it will boot directly into Rockbox without the Sansa firmware doing its refresh of media. If you've just finished a file operation, make sure you wait a few (10-20) seconds before powering down, just to be safe.
This works for the refreshing after charging. However, my device also refreshes right after I plug it in (Win7), and it takes tons of time with the 32GB card until it's done and I can finally access the memory.

Any ideas?