Thank You for your continued support and contributions!
- on an older refurb both builds crash very fast (browsing the file system, FF through an mp3). With an SDcard even worse.
BTW, it seems the patch that prevents the click when traversing the -40 volume value is not included (posted by Mihail in this thread).
Quote from: johnb on August 09, 2015, 05:42:02 AM- on an older refurb both builds crash very fast (browsing the file system, FF through an mp3). With an SDcard even worse.Can you test this build: http://knk.zz.mu/rb/clip+.zip ?Quote from: johnb on August 09, 2015, 05:42:02 AMBTW, it seems the patch that prevents the click when traversing the -40 volume value is not included (posted by Mihail in this thread).All audio patches already commited to rockbox. We switch audio mode when traversing the -40 volume value, so small click unavoidable.
your build works fine, I couldn't break it so far ;-)
I DON'T hear the click in the current dev builds nor yours, but in the one by LolaPalocz.
Quote from: johnb on August 09, 2015, 01:46:29 PMyour build works fine, I couldn't break it so far ;-)Can you also test next two builds?http://knk.zz.mu/rb/clip+_20.ziphttp://knk.zz.mu/rb/clip+_21.zipQuote from: johnb on August 09, 2015, 01:46:29 PMI DON'T hear the click in the current dev builds nor yours, but in the one by LolaPalocz.Very strange. You should have small clicks/distortion on all builds. Better do cold restart (power off and than power on) after installing new build.I hear more noise and have more power consumption when restarting without power off.
(you miss usb patch: http://forums.rockbox.org/index.php/topic,48549.msg233822.html#msg233822).
I have to take some of my statement back: If I pause playback and the change the volume, I do hear a click, but don't notice during playback.In the one by LolaPalocz, it's very noticable also during playback.
- amsv2_scaling_v8+gui_boost+restore_irq+CVDD2_113 ... I already noticed estimated autonomy looks funny, don't know if Rockbox is lost with the battery improvements. The remaining power percentage shown sometimes jitters: 75% is displayed, then 74%, 75% again and few seconds-minutes later it's back to 74%. Shall I reset anything in order to have it properly calculated, and have it taken into account by Rockbox Information panel ?
Had only one issue: at power on, load was stuck displaying Rockbox logo step; ejecting the card, power on + loading the card after the Clip had properly started was enough.
Using clip+_20, while listening to music and no particular activity, I suddenly face a crash with "data abort" like in this snapshot or the music stops playing and I have a black screen.In either case pressing the power button for > 10sec is needed to be able to reboot.
I guess it wasn't essential for me
Dunno how much more power is used with 113 vs 111.
I dont think there's anything to reset, rockbox on the clips just follows a static table battery voltage => % left, so if it quickly goes up and down and up, it's because the battery voltage does this.It's probably because of the gui_boost patch, which may suddenly draw more power, thus reducing the voltage (so the %). When boost mode is exited, less power is drawn, the battery is happy and shows more voltage (so the %). I wouldn't worry.
In terms of getting something we could commit, I would really like to see fully stable frequency scaling (ideally on all AMSv2 players) at stock voltages first.
Then we could commit that and work on voltages. Otherwise its very hard to know what is broken when someone reports a random crash.
I will revisit http://knk.zz.mu/rb/clip+.zip with that flac album.
Page created in 0.107 seconds with 21 queries.