Thank You for your continued support and contributions!
Petur, did you test the 2GB auto-split since you removed boosting? Saw you mentioned that there seemed to be a gap in playback, so I'm just making sure that is is just an issue with long wav playback, not the actual recorded files not being seemless...cos it was working ok a couple of months ago (last time i tested).
Is this compatible with the AGC patch?
The answer is yes. I record quite regularly, so I'll report back if I have any problems.
I just had an idea for the REP...wouldn't it be nice if there would be the possibility topress the left record button in order to get to therecording screen instantly?
Quote from: lurker on June 19, 2006, 08:47:21 AMI have "Show Recording Screen on Startup" set to "yes". When I startup, I'm immediately on the recording screen and everything is fine EXCEPT I can't monitor audio through the headphones. The level meters are responding and it in fact records just fine, I just can't hear a thing. To actually hear the audio, I need to press "Stop" to go to the "Recording Screen|Recording Settings" screen and then if I go back into the "Recording Screen", everything is fine.This happens with headphones plugged into the remote or plugged directly into the main unit.Just checked this and it works fine on my h340, so the cvs build used with line-in and mic should be ok. Just can't test spdif...
I have "Show Recording Screen on Startup" set to "yes". When I startup, I'm immediately on the recording screen and everything is fine EXCEPT I can't monitor audio through the headphones. The level meters are responding and it in fact records just fine, I just can't hear a thing. To actually hear the audio, I need to press "Stop" to go to the "Recording Screen|Recording Settings" screen and then if I go back into the "Recording Screen", everything is fine.This happens with headphones plugged into the remote or plugged directly into the main unit.
Would it be possible to integrate AM-radio?
Be warned that there's possibly lost samples in the filesplit (until I can investigate this). It should be save if you stay below 2GB and don't use the timesplit feature...
Quote from: petur on June 19, 2006, 03:29:50 PMQuote from: lurker on June 19, 2006, 08:47:21 AMI have "Show Recording Screen on Startup" set to "yes". When I startup, I'm immediately on the recording screen and everything is fine EXCEPT I can't monitor audio through the headphones. The level meters are responding and it in fact records just fine, I just can't hear a thing. To actually hear the audio, I need to press "Stop" to go to the "Recording Screen|Recording Settings" screen and then if I go back into the "Recording Screen", everything is fine.This happens with headphones plugged into the remote or plugged directly into the main unit.Just checked this and it works fine on my h340, so the cvs build used with line-in and mic should be ok. Just can't test spdif...Works ok on mine too with the patch applied (but again no spdif test). Lurker...does it work properly with default settings?
Any other tests anyone can suggest?
Have you tried resetting your settings to clean the slate then changing only the 'show recording screen on start up'? Let us know if that is still demonstrating the same problem. If its not, then change your options one at a time back to what they were pre-reset until you find the gremlin.Are you running the headphones out of a remote btw, or out of the main unit?
When rockbox asks you to press play (when resetting) it means click the joystick in. To reset at startup just press the on button to start and then hold down the record button (it will say "cleared" in the centre of the screen.
Note that Page 12 of the latest PDF manual for the iriver shows a picture and both in the picture and text, Play is the button above Stop and the joystick press is Select.
Back to the issue at hand...After doing a reset, if I change ONLY "Show Recording Screen on Startup" to "yes" then power off and back on, I have the exact same problem (except I'm obviously using the internal mic instead of my external mic).So, on my h140, reset to default, change "Show Recording Screen on Startup" to "yes". Every subsequent power on requires me to press Stop then Play to exit and re-enter the recording screen before any audio comes from the headphones. Happens both on the remote and main unit.Is no one else with a h120/h140 seeing this with the REP sw build I'm using? Again, it's build 060604-1858. Is there a newer REP build one I should be running?I may be able to get access to another h140 to try, if the concensus is that it might be my hardware.
Well I'm using exactly the same build as you so that isn't the problem....I must say I'm a bit stumped....It seems unlikely to me that it is hardware but it seems to be pointing that way... hmmmm I'll keep thinking about it.
Page created in 0.046 seconds with 21 queries.